                                     
These cards are designed to fit vintage and replica graflex clamps. These are all 2" long x 0.625" wide x 0.063" thick unless otherwise specified. Not all clamps are created equal. Some sanding may
be required if your card fits too tightly.
Ask about bulk orders of 100 or more for your saber runs. Bulk orders get the name of your company/title of your run on the edge of the card
Please allow up to ten working days to get your order shipped. I solder these by hand, and have experienced an unprecedented amount of orders for these. Thank you for your patience!
Order below:
BOLD indicates most screen accurate version
Please Note: While I attempt to provide the most accurate and high quality cards I possibly can, please understand that, where possible, these clamp cards are manufactured the same way the vintage PCBs were made that were used in the props. As such, they go through manufacturing processes and handling that could possibly leave minor scratches in the gold, or other manufacturing defects. When applying silver solder to a solder card order, minor imperfections may be introduced as well. These should not detract from the overall quality of your card. However, if you recieve a card that you are unsatisfied with, please contact me.
DOMESTIC Shipping Included. INTERNATIONAL CUSTOMERS: Due to recent rate increases from USPS, shipping outside of the continental USA will be calculated based on total order as follows: $25 and under will be a $10 charge for shipping.
$25.01 to $50 will be a $5 charge for shipping.
$50.01 and up will be free shipping.
PLEASE do not ask me to declare a value below what is ordered. That is against my policy.
 
 
|
Slothfurnace Vader Barbican
These are designed to fit an MPP vintage or replica clamp
1.55" x 0.59" | 39.37m x 14.986mm
Plain - Gold plated, no silver solder: $13
Silver Solder on ESB Otis Side A: $17
Silver Solder on ESB Otis Side B: $17
Silver Solder on both sides: $21
Silver solder traces textured and card aged:
Vintage Finish side A: $23
Vintage Finish side B: $23
Vintage Finish both sides $30
|
  
|
Slothfurnace ANH MPP Exactra
These are designed to fit an MPP vintage or replica clamp under the bubble strip for a Vader ANH V1 lightsaber - no trimming needed.
1.57" x 0.733" | 39.9mm x 18.61mm
Plain - Gold plated, no silver solder: $13
Silver Soldered square LED pads: $17
Vintage Finish - Silver soldered and aged: $23
|
  
|
Slothfurnace Special Edition 2020 SE
Translucent base with black soldermask and white silkscreen on one side, translucent base exposed with metallic finish on the other. Cooling plates have a metallic finish on both sides. Can be used for capacitive touch pads.
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
|
 
|
Slothfurnace ROTS Vader
These are designed to fit an MPP vintage or replica clamp for a Vader ANH V2 Variant lightsaber. 1.725"x0.719"
I've had numerous requests for these over the years, and now I've finally had a chance to add them to the shop.
These cards are silver plated at the factory, and come with a matte finish which can be polished to a shine.
Plain - Silver plated: $13
|
  
 
 
|
Slothfurnace ANH Vader V2
These are designed to fit an MPP vintage or replica clamp for a Vader ANH V2 Variant lightsaber. 1.725"x0.719"
These have been painstakingly recreated from vintage Exactra boards. The LED multiplexing circuit inherent in the display boards is preserved. If one were to solder wires to the cathodes, and insulate and apply 1.5 volts to the anodes, one would be able to light up the LEDs on the board. ONLY TESTED ON A AND B STYLE LEDS. Contact me with any questions:
bradley@slothfurnace.com
ANH V2 A Fully Assembled Board:
"A" style LEDs no longer available.
ANH V2 B Fully assembled Board:
"B" style LEDs no longer available.
ANH V2 C Fully assembled Board: $100
DUE TO DISRUPTIONS IN SUPPLY, LEDS NOT AVAILABLE
please email me if you have questions about this.
ANH V2 Board Only (NO LEDS INCLUDED): $19
Use these instructions for "C" style LEDs also.
|
|
Slothfurnace TROS Rey: $12
I was fortunate enough to make these for the Disney Galaxy's Edge Rey Display saber. 1.379"x0.591"
|
 
 
|
Slothfurnace Radiator Fins
These are , with mounting holes that match popular DIY saber chassis. The larger outer radiator holes accept 1/16" inch rod or tubing, the inner, smaller radiator holes accept 0.032" rod or tubing. The two wire conduit holes accept wire bundles or tubing at 0.125" diameter. These can be mounted with three 4-40 rods/screws equally spaced, or two 4-40 rods/screws directly across from each other, such as the mounting example to the left.
1.24" diameter, Gold Plated, Natural color board:
$5 Each or Five for $20
1.24" diameter, Gold Plated, Black color board:
$5 Each or Five for $20
1.406" diameter, Gold Plated, Black color board:
$5 Each or Five for $20
These are sized a bit larger diameter to fit Graflex and MPP replicas. Will interface with the same tubing and mounting holes as the 1.24" fins.
|
|
Slothfurnace Celebration 2019 SE: $13
Translucent base with authentic Star Wars control panel patterning. Great for backlighting!
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
|
  
|
Slothfurnace ROTJ Hero Wide Blue
As close to the screen-accurate blue as some people say. Solder points on the back connect to front and back stripes on the top card for capacitive touch activation/aux.
The first and last four exposed copper traces on either end of the card connect to the exposed copper traces on the back of the board.
Wide sized to fit most if not all ROTJ Control boxes.
2" x 0.708" x 0.0625" | 50.8mm x 17.98mm x 1.58mm
Standard Copper, no silver solder: $13
Polished Copper, no silver solder: $21
Factory Blemish - Smudges or slight scratches from factory: $9
|
  
|
ROTJV2/ROTJ Stunt Gold Clamp Cards
ROTJV2 on one side, ROTJ Stunt / Ep 7, 8 on the other
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
Plain - Gold plated, no silver solder: $13
Silver solder thin traces on ROTJV2 side: $17
Silver solder traces textured and card aged -
Vintage Finish side A: $23
|
 
|
Slothfurnace TLJ Creepy Uncle
The Last Jedi card from the "Creepy Uncle" scene. Gold plated raised traces against matte black soldermask. May need to be trimmed on the ends to fit shorter control boxes such as Romans.
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
Plain - Gold plated, no silver solder: $13
Silver Soldered and Polished: $30
|
 
|
Slothfurnace IMP Celebration 2017 SE
Translucent base with authentic Imperial patterning. Great for backlighting! Given out at SWCelebration 2017, now available.
Special Edition: $13
Extra Dark Edition: $13
MUCH less light pass-through, may vary. Limited Stock!
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
|
     
|
ESB Otis A/ESB Otis B Clamp Cards
Meticulously recreated from a vintage Otis Elevator card, these have identical variously offset thin traces to the Otis card on side A, and "idealized" consistently centered thin traces on side B.
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
Plain - Gold plated, no silver solder: $13
Silver Solder on ESB Otis Side A: $17
Silver Solder on ESB Otis Side B: $17
Silver Solder on both sides: $21
Silver solder traces textured and card aged:
Vintage Finish side A: $23
Vintage Finish side B: $23
Vintage Finish both sides $30
|
     
|
ESBA/ESBB Clamp Cards
Thick traces on one side, Thin traces on the other
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
Plain - Gold plated, no silver solder: $13
Silver Solder on ESB Side A: $17
Silver Solder on ESB Side B: $17
Silver Solder on both sides: $21
Silver solder traces textured and card aged:
Vintage Finish side A: $23
Vintage Finish side B: $23
Vintage Finish both sides $30
|
 
|
ROTSA/ROTSO Clamp Cards: $13
ROTS Anakin on one side, ROTS Obi on the other
Gold plated & black soldermask on both sides
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
|
  
|
ROTJ Hero & Stunt Clamp Cards
ROTJ Hero on one side, ROTJ Stunt on the other
Bare copper & matte black soldermask on both sides
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
Plain - Copper, no silver solder: $13
Copper Polished: $17
Factory Blemish - Smudges or slight scratches from factory: $9
|
 
 
|
TFA Left or right-handed thin traces
TFA pattern on side A has left-handed thin traces
TFA pattern on side B has right-handed thin traces
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
Plain - Gold plated, no silver solder: $13
Silver solder TFA L thin traces: $17
Silver solder TFA R thin traces: $17
Silver solder thin traces both sides: $21
|
 
Shown on top of one another to display translucency. Only card on top is included.
|
TFA Translucent Left Trace One-sided Clamp Card
Translucent PCB, Gold plated traces, opposite side is blank
NOTE: Due to manufacturing issues, these may be more or less translucent.
2" x 0.625" x 0.0625" | 50.8mm x 15.8mm x 1.6mm
Plain - Gold plated, no silver solder: $12
Silver Solder Thin Traces: $16
Sold out/discontinued |
 
|
MPP Exactra replica clamp card - Green
Green PCB, gold plated traces, replicated from vintage Exactra card. Will need to be trimmed to fit your MPP clamp.
2" x 0.625" x 0.0325" | 50.8mm x 15.8mm x 0.83mm
Plain - Gold plated, no silver solder: $13
Silver Solder square LED pads: $17
Temporarily sold out.
|
 
|
MPP Exactra replica clamp card - Blue
Blue PCB, gold plated traces, replicated from vintage Exactra card. Will need to be trimmed to fit your MPP clamp.
2" x 0.625" x 0.0325" | 50.8mm x 15.8mm x 0.83mm
Plain - Gold plated, no silver solder: $13
Silver Solder square LED pads: $17 |
   
   
  
This site sand my works have been featured by the kind folks below. Thank you so much from the bottom of the slothfurnace!
ANH Obi Epic Reveal was the grand prize winner of the 2012 Instructables/Thinkgeek Sci-Fi contest
MSNBC Today - c|net feature and gallery - SWTORStrategies.com - 8BitDad
Notcot.org - GeekTyrant - The Escapist on the ROTJ Luke - WIRED - Geekologie - Gizmodo - The Daily What
MAKE Magazine: ROTJ Luke - Hack a Day: ROTJ Luke - Slothfurnace on Reddit - Slothfurnace gets Slashdotted
The Escapist on the ANH Luke - Neatorama - io9 - ANH Obi on MAKE Magazine's blog - Hack a Day: ANH Obi
BioWare's The Old Republic lightsaber assembly (
I made the pieces in the cinematic to match my ANH Graflex internals.)
|
